Linksys EA9500 setup or Linksys EA9500 router setup is very easy and simple. To access the Internet through the wireless network with a Linksys router, you essentially need to set up the router with the modem. Make sure you finish reading this blog.
However, before beginning the Linksys EA9500 setup process, it is important to understand the features and specs the networking device has to offer because, no matter what you purchase, it must be used properly by you. The router configuration includes MU-MIMO technology, which enables automated connection to the strongest wifi signal as you move about your home or office. You may customise the Linksys EA9500 firmware update, setup wizard, parental controls, , and a tonne of other things.
Things you should have before you Setup Linksys EA9500:
- Ethernet wires, two
- one piece of equipment
- a properly functioning Internet connection and a home modem
- 192.168.1.1 is the IP address.
- Default Network SSIDs are listed on your Linksys device’s back label.
- Web-based SSIDs’ Username and Password fields should both be left blank (admin)
Setup Linksys EA9500 Max-Stream Router
Here, we’ll walk you through the actions required to finish the Linksys EA9500 setup procedure. Make sure you follow the procedures listed below exactly to avoid running into problems.
1. Setup of Hardware
Let’s begin by discussing the Linksys router hardware configuration.
- Take an Ethernet wire for the following step and connect the antennas to the router.
- Connect the cable’s other end to the LAN port on your Linksys router. Incorporate the other end into your modem’s LAN port.
- Ensure that the Internet cable is securely fastened to the modem and is not loose.
- To put the router into functioning mode, connect the power wire to it and plug it into an electrical outlet.
2. Configuration
You must now access the Linksys router. Open a web browser on your PC after connecting it to the wireless network.
- To access the Linksys router login page, enter the Linksys router IP address in the address area.
- Now enter the admin password in the Linksys login box and press Submit.
- You will now be sent to the Linksys router setup page by the browser.
- Click on the Wireless tab on the left panel.
- To set up the Linksys router, start with the setup wizard and adhere to the on-screen directions.
- After that, be sure to save the change on your router.
- Your wireless-capable devices can access the Internet now that the router has been configured.
How to Setup Linksys EA9500 Smart Wifi Router As An Access Point?
You can use the bridge mode setting on your Linksys Smart Wi-Fi Router to:
- Connect two (2) routers that can share resources on the network.
- Utilize the router as an additional access point for a network that already exists.
- Connect the router to your Internet service provider’s modem or router (ISP)
- To use the router with other devices, disable some features.
NOTE: Activating Bridge Mode on your Linksys Smart Wi-Fi Router will remove all of its router features and convert it to an access point. The router’s built-in firewall and NAT functions will no longer function, and it will stop serving as a DHCP server.
Here’s how to setup Linksys EA9500:
Step 1: Any of the numbered ports on the router that supports bridge mode should be connected using an Ethernet cable from your PC. For the time being, don’t attach anything to the Internet port.
Important: Make sure to have an Ethernet cable attached to the router that was configured to operate in bridge mode. It is NOT supported to establish up a wireless connection between the two (2) routers in this configuration.
Step 2: Connect the power adapter’s other end to the Linksys router and plug the other end into an electrical outlet.
Step 3: After that, open a web browser and type the IP address of your router into the Address bar. Then, click [Enter]. A Linksys router’s default IP address is 192.168.1.1.
Step 4: The username and password for the router will be requested. The router’s default username and password are admin; enter these in the appropriate fields, then click OK. Other router models leave the username blank and use admin as the password.
Step 5: Check the box next to “Don’t show me this again” after the warning window appears, then click OK.
Step 6: The online setup page for the router will then be displayed to you. Set the Internet Connection Type to Bridge Mode under Internet Setup.
Step 7: Change the router address setting to “Specify an IP address” and then input the correct Linksys router’s IP address, Subnet Mask, and Default Gateway before clicking “Save Settings”.
Step 8: The Linksys router’s Internet port should be connected to the primary router.
With the Classic firmware, your Linksys Smart Wi-Fi router is now configured for Bridge Mode. Now that it can serve as an access point, it can help you grow your wireless network. So this is how you’ll setup Linksys EA9500.
How to Update Linksys EA9500 Firmware?
For Linksys EA9500 Firmare update we will follow the following steps:
Sign in to your router.
Find out what firmware version your router is currently using before you begin. You must sign into your router in order to accomplish it. You can get step-by-step instructions for logging into your router at Router Check.
Ascertain the firmware version of the router.
Find the firmware version by browsing the router’s interface. It must be displayed in a visible location.
Ascertain the most recent firmware release.
Inquire about getting latest firmware by visiting the router manufacturer’s website. To find the most recent firmware version for your router model, see the download area. You can obtain firmware from the vendor’s support website by clicking here.
Download the newest firmware.
You do not need to take any further action if your router is already running the most recent firmware. If not, then you should download the most recent firmware to your computer. Make careful to obtain the precise firmware your router requires. It’s crucial that the firmware and router model match exactly. Additionally, the revision numbers for the router models frequently need to match.
Upload the Linksys EA9500 Firmare update.
In the previously opened browser window, go back to the router’s interface. See how to upgrade the router’s firmware by going to the administrator page.
Watch for the miracle to occur.
If everything has been done correctly up to this point, your router should be loading the updated firmware. Wait until the procedure is finished before turning off the power to your router.
The router reboots
The router should reset itself after receiving updates. Relogin to the router after the reboot to see if the version number has changed.
This will help you in Linksys EA9500 Firmare update.
How to Reset Linksys EA9500?
There are times when there is no other solution to reset your router to its factory default settings, when you are resetting it – you should know how to reset it. Before that always be sure of aspects such as proper internet connectivity, no loosened or worn-out cables, power switches should be on, you must be entering all the figures & digits correctly, and timely updated firm wares. Because these are some silly mistakes we often do.
Here are the steps that you may follow.
- Keep the router powered-on.
- Next, you may press the reset button on your linksys device.
- Then, release it after ten seconds, watch for LED behavior.
- After that, you have to power cycle your router.
By now, the Linksys EA9500 has reached back to its factory default settings.
How to Fix Linksys EA9500 No Internet Connection Issue?
Here’s what to do when there is a no internet connection issue:
- Your internet service provider’s modem must be disconnected from the power supply.
- After that, visit the Linksys router’s web-based setup page.
- Go to the main setup page and then select the Mac address clone sub-tab.
- After selecting enable, manually type the Mac address into the empty fields.
- After that, go to the status tab after saving these settings. The Ethernet adapter is a crucial component that you must not overlook.
- The internet Mac Address must match the command prompt. Then, turn off the router and unplug it from the power supply if you are very certain that they match.
- Reconnect the modem to the power supply and wait for all of the lights to come on at once, both upstream and downstream.
- After that, power on your router and wait for the lights to synchronise to resolve the Linksys router No internet access issue.
- To verify your internet service provider’s IP address, gain access to the router’s web-based setup page and choose the status tab.
- The status screen of the Linksys router will now show the modem’s IP address. Now that your web browser is open, you can visit any website to test your internet connection.
FAQs:
What is Linksys EA9500 Default Password?
Your Linksys EA9500 router’s default password is admin, and the default username is unknown.
Is Linksys EA9500 Smart Wifi Router Alexa Compatible?
In order to enable manufacturers to add “skills” that allow Alexa to operate the devices and carry out various tasks, Amazon has been particularly aggressive in integrating Alexa support to even more third-party solutions.
Linksys wireless routers and mesh networks, including those from the Velop, WRT, and Max-Stream families, have been added to the list of Alexa devices that are supported.
You must make sure that each Linksys device has a Linksys Smart WiFi account set up and configured in order to enable Amazon Alexa functionality.
You’re already set up if you have a Velop mesh network because a Linksys account is necessary.
For other Linksys devices, an account is not required, so create one now.
You can then launch the Alexs app on your smartphone after that is finished. Then, go to the menu and select Skills. After that, choose “Linksys” from the search results after selecting the Search box. You may view the skill description and trigger examples on the same page as you tap the Enable button to activate Alexa for that device.
Does Linksys EA9500 Support VPN?
VPN traffic is automatically provided to routers like the Linksys EA9500 for distribution through them. This capability can be used by users who have VPN servers or VPN clients installed on their network.
Can I Use Linksys EA9500 As a Repeater?
Wireless Repeater mode is supported by a few Linksys Smart Wi-Fi routers. Log in to the router’s web-based setup page and select Connectivity > Internet Settings to see if this feature is available.
- To log in to your Linksys Smart Wi-Fi router, type “http://192.168.1.1” into your web browser’s address bar.
QUICK TIP: The Linksys router’s default IP address is 192.168.1.1. Use the new IP Address if it has been changed.
- Click Connectivity.
- Simply select Internet Settings.
- Then, click Edit.
- Select Wireless Repeater.
- After that, enter the main router or access point’s Network name (SSID), Network band and Security mode.
- Click yes to save settings.
Once your Linksys Smart Wi-Fi router is turned into a Wireless Repeater, you will need to check on your main router or access point’s DHCP Table for the new IP Address of your Linksys Smart Wi-Fi router. You will have to use this new IP Address to log in to the router’s web-based setup page if you need to configure it later on.